E-Spray  Electrostatic  Battery Powered Sanitisation System   

For perfect 3d coverage of all surfaces.

The convenience of a handheld Lithium battery powered device with the outstanding performance of electrostatic-ally charged diffusion.

The disinfectant solution is sprayed through the nozzle which imparts an electrostatic charge to the solution being diffused in very fine particle sizes.

This electrostatic charge attracts the disinfectant particles to all contact surfaces preventing them from falling uselessly to the ground. It also ensures a perfect three dimensional blanket covering of all surfaces, including curves and even the hardest to reach areas, creating a sanitizing coating.

How Does It Work ?

Electrostatic hygienization allows to coat a surface quickly and evenly with a sanitizing solution. The electrostatic applicator provides an electrical charge to the solution. The charged molecules repel each other, so they keep an even distance from each other but, at the same time, they are attracted to the surface to be treated. The strength of the charged particles is greater than that of gravity, so they are immediately attracted by the surface and do not fall to the ground. The attraction therefore ensures that all the particles of the solution settle on the surface, thus creating a 360-degree coverage, without leaving out any areas.

Why Do You Need E-Spray ?

Germs and bacteria are very quick to spread and settle in tight corners and hidden spots. Disinfecting effectively by hand takes a very long time and requires prohibitive costs. In addition, there are many areas that are difficult to disinfect properly, such as computer keyboards and telephones in offices, or checkouts in supermarkets or shops. An electrostatically charged spray can reach the entire targeted area evenly, right down to the most hidden points. The cloud of charged particles completely envelops the surface and sanitizes every part of i

System Benefits of Fine Micronized Spray.

The Strength of the charged particles is greater than the gravity, so they are immediately attracted by the surface and do not fall to the ground. 

Reduction in chemical consumption by up to 65%. 

Saving time and money.

Energy saving.

Environmentally friendly.

System Function.

1. The electrostatic applicator provides an electrical charge to the disinfecting solution.

2. Charged particles are attracted to the surface.

3. Surfaces are reached and coated by the micronized solution.

4. Each surface is evenly covered with the micronized solution.

5. Compatible and safe for use with a wide variety of disinfectants, including hydrogen peroxide solutions, Quaternary ammonium and chlorine-based solutions.

Recommended Applications.

OFFICE.

• Meeting rooms

• Restrooms

• Workstations (desks, chairs)

• Furniture

• Refreshment areas (coffee machines, vending machines, coffee tables)

• Access/exits: handles, grab bars, handrails, elevators

• Counters and furniture in public spaces

FACTORIES.

• Workbenches

• Locker rooms

• Restrooms

• Counters and welcome areas for suppliers/customers

RETAIL (NON-FOOD).

• Customer areas (dressing rooms, treatment rooms, waiting rooms)

• Goods and shelves

• Workstations (cash registers, counters, furniture)

• Restrooms

TRANSPORT.

• Passenger seats

• Handles, doors, bars, buttons

• Restrooms

• Luggage drop-off areas

• Overhead lockers and storage areas

• Validating machines

• Meeting rooms

• Classroom/ auditorium seats

WELLNESS.

• Equipment

• Locker rooms

• Waiting rooms

• Relax zones

• Treatment rooms

HO.RE.CA.

• Rooms

• Restrooms

• Waiting rooms

• Counters

• Seats

• Furniture

EDUCATION.

• Desks and furniture

• Toys and equipment

• Doors and handles

• Restrooms

• Waiting rooms

• Counters

• Locker rooms

• Classrooms

• Offices and workstations

• Relax zones

• Meeting rooms

• Classroom/ auditorium seats

CONSTRUCTION SECTOR

• Work vehicle cabins

• Company cars

• Locker rooms

• Restrooms

• Refreshment areas

E-Spray Plus  Information.

Three different-sized nozzles at 40 μm – 80 μm – 100 μm are supplied with each device to adapt the particle size according to the needs of the application and according to the desired solution consumption rates.

18 Volt - 2Ah Li-ion Battery and Fast Charger 2 Ah included. 100% recharge in 1 hour.

Convenient shock-proof carrying case included.

Built-in nozzle holder.

Shoulder strap attachments.

Ergonomic handle.

Battery charge level indicator.

18 Volt  Lithium battery (3 hours running time).

NOZZLES:

40 μm particles (22’ of autonomy).

80 μm particles (12’ of autonomy).

100 μm particles (8’ of autonomy).

Tank 1 Litre.

Optional backpack with additional 2-litre solution tank.

TECHNICAL SPECIFICATIONS of  E-Spray Plus.

Power supply V 18 V - 2 Ah Li-ion Battery (Standard) 18 V - 4 Ah Li-ion Battery (Optional)

Battery charger V/Ah 110-230 V/0,4 Ah

Pump power W 20

Pump flow rate ml/min

45 (with 40 μm nozzle)

77 (with 80 μm nozzle)

138 (with 100 μm nozzle)

Solution tank capacity liters - 1

Nozzle size micron - 40 /80 / 100

Productivity (max) m2 -  350

Tank autonomy minutes - 22 (40 μm) - 12 (80 μm) - 8 (100 μm)

Battery run time hours - 3 Hours with 2 Ah Battery  (6 hours with optional 4 Ah battery)

Weight -   1.7 Kg  Including  2 Ah Battery, (2.7Kg Including Battery & Solution)

Dimensions CM 42x28x9.5

SANIQUE S3I ELECTROSTATIC SANITISING SPRAYER

The Sanique S-3i Sanitising Electric Sprayer has been designed to meet the demands that the professional first-responder sanitising contractor faces. It’s delivered as a totally stand-alone unit that’s ready for immediate use (the

only extra is the appropriate disinfectant and a power source).

In addition to direct human-to-human transmission, contaminated surfaces also pose a risk of transmitting viruses and pathogens. Especially in the current COVID-19 pandemic, this is of great importance: Studies show that SARS-CoV-2 viruses can survive for several days on surfaces that we come into daily contact with.

Disinfecting areas can be undertaken with a range of different disinfectants. Application of the disinfectants comes down to 3 main methodologies - wiping, spraying. Spraying have the advantage of speed, covering large areas quickly & effectively.  Atomising the disinfectant at 10-30 microns is the optimum to achieve this. The Sanique S3I  Electrostatic sprayer is specifically designed to achieve this rate giving cleaners the capacity to use  spraying application depending on the particular requirement of area being treated & type of disinfectant used. The other important point is the rate of spray penetration into hard to reach areas so that the disinfecting process is completed properly. The Sanique S3I  Electrostatic  sprayer achieves up to 95% penetration to target area.

The Sanique S3I Electrostatic Sprayer  has been created specifically for the application of all government approved disinfectants and other sanitising fluids that will ensure maximum surface coverage and fogging in one pass.

 Sanique S3I Electrostatic  sprayer is supplied ‘ready to go

FEATURES:

Slow-stroking durable DC Motor

The S3I Electrostatic sprayer has a powerful, slow stroking motor, which is fully enclosed, with a durable gearbox with a single gear. Simple and reliable for long, serviceable life.

Large, Slow Stroke Piston.

Unique in small sprayers, the S3 electric sprayer has a large, slow stroke piston delivering class leading performance. And with added benefit of greater durability. Less pump strokes per litre of sanitiser means less wear & tear hence less downtime.

The S3 Unit has a set Pressure.

Extension Spray lance allows you to reach into hard to reach places.

Easy Maintenance for Long Life.

The S3 packing kit are easily adjusted from the outside of the pump, extending the life of the packings, reducing repair costs and downtime.[/vc_column_text][/vc_column][/vc_row].

The Sanique S-3 Sanitising Electric Sprayer has been designed to meet the demands that the professional first res-ponder sanitising contractor faces. It’s delivered as a totally stand-alone unit that’s ready for immediate use (the only extra is the appropriate disinfectant and a power source).

CONSIDER THESE ADVANTAGES

◼ Rapid deployment

◼ Tough construction copes with rigorous on-site situations

◼ Light weight - under 12kg for easy handling by operatives

◼ 15m hose ensures minimum movement of machine - set up, and it’s simple to work on sanitising within the reach of the hose with only the gun in your hand

◼ Includes a specifically designed spray tip that ensures maximum surface coverage and fogging

◼ Full 2-year manufacturer’s warranty

THE SANIQUE S3I  PACKAGE

◼ Machine complete and ready to go for all sanitising procedures

◼ 15m hose for maximum flexibility, (Option 30 metres of hose if required

◼ 380mm (15”) lance to ensure reach into those otherwise hard to-get-at areas

◼ Ergonomically designed gun to minimise hand and wrist fatigue

◼ Specific sanitisation spray tip to ensure correct atomisation (Between 10-30 Microns)

SPECIFICATION

• Weight             11.4 kg
• Atomisation   between 10 & 30 microns
• Motor             240 - 110 v - 700 Watt
• Spray tip          fan width 10"/ 25.4cm
• Set flow rate   0.34 litres per minute 
• Coverage        30/40 sq metres per minute
• pump              1100 psi 
• Cable length  2.2 metres
• Warranty         2 years

SaniMist Sanitization System       

1. Fine Micronized Aersol Mist.

2. One Single quick operation the entire area is Sanitize- No Need to Wipe , Dry Surfaces.

3. Speed and Efficiency.

4. Reduction in chemical consumption by up to 95 %.

5. Saving Labour time and Money.

6. Environmental friendly.  

USES.

High contact surfaces are effortlessly and efficiently sanitized.

Perfect for the disinfection and odor control of Car interiors.

Can also be safely sprayed through climate control air ducts of automobiles, as well as Traffic & Transport Industry, Aviation & logistics, Domestic Houses, Commercial buildings, Retail Properties, Hospitals, Care-homes,Engineering, Manufacturing ,leisure, Hotels, Hospitality Events, Doctors Practises, Veterinary, Dentists, to safely  Sanitize and deodorize all surfaces.

Compatible and safe for use with a wide variety of disinfectants, including hydrogen peroxide solutions, qua-ternary ammonium and chlorine-based solutions.

OPERATION.

The exclusive nozzle is the point at which the solution is mixed with air, resulting in an aerosol mist.

The oversized easy to press lever on the handheld trigger mechanism provides one-handed operation and control.

The spiral tube connecting the nozzle to the machine contracts down to a very small size when not in use but can be elongated up to 3 meters during use to reach areas which would normally be impossible to target.

This mist is diffused quickly and evenly throughout the target area, remaining in the air before settling on surfaces, even in the hardest to reach areas, thereby disinfecting them.

Built-in hook to stow the cover lid during solution filling (SaniMist model). Easy to access inner compartment makes maintenance and solution filling a very easy task.

Convenient hand-nozzle support.

SANIMIST TECHNICAL SPECIFICATIONS  

Voltage - Frequency V-Hz 230 - 50 

Compressor power 350 Watt 

Pump power  16 Watt

Total power  366 Watt

Compressor flow rate liters/min 55 

Pump flow rate ml/min 40 

Solution tank capacity liters 3 3

Solution consumption rate ml/min 40

Equipped with integrated timer Yes

Programmed time interval minutes 20

Spiral tube maximum length m 3 3

Power cord length 10 Metres

Dimensions cm 37x37x81

Weight 18 KG

PRODUCT DETAILS & SPECIFICATIONS Zoono Z71 Microbe Shield Surface disinfectant and protector 

 Zoono Microbe Shield is both a disinfectant and an antimicrobial surface coating.  The technology is designed to kill microorganisms as any other conventional disinfectant except one dry leaves an antimictobial layer that remains active as a biocide for extended periods of time depending upon the environment treated. 

 The technology is based on a silicone polymer capable of binding to most surfaces by covalent bonding.  This enables the layer to withstand on-going cleaning procedures that are paramount to ensuring optimum antimicrobial activity.  The technology is not in any way a replacement for cleaning, to include most conventional sanitisers and detergents if need be. Zoono Microbe Shield enhances any hygiene process by providing on-going antimicrobial activity between cleaning to help combat microorganisms coming into contact with the surface from people, the air and any other source of contamination. 

 Zoono Microbe Shield is a water based disinfectant that is safe to use and once dry continues to be active.  The product has been tested to EN 1276, 13697, PAS 2424 and 14476 against bacteria, fungi, yeasts and enveloped viruses. 

 In the absence of any official EN/BSI test for residual antimicrobial activity, Zoono MIcrobe Shield was tested by reverse engineering an EN test for non-porous surfaces EN 13697 by a UKAS accredited UK laboratory, as this includes full experimental validation and control. The test verified that Zoono Microbe Shield remained active for up to 30 days​ ​against bacteria.  In areas where there is more rigorous physical cleaning, or where there is a higher infection risk application frequency may be increased based on a risk analysis. 

* Testing has been carried out in a “live” high contact environment and further testing will be undertaken in accordance with EN and BSI guidance once authorised and regulatory approved methods are available. A technical report on the testing and results are available upon request. 

 DIRECTIONS FOR USE 

 It is extremely important to thoroughly clean the surface prior to the application to remove any interfering soils so that the polymer can bind to the surface.  Once dry Zoono Microbe Shield can be applied by spray and wipe with a microfibre cloth or for larger areas using “whole technologies” or more recent application technologies such as electrostatic spraying. Once dry the surface will have established the antimicrobial polymer coating. 

Conventional cleaning can continue after the surface is treated and dry and is essential as part of any hygiene procedure and to maximise the antimicrobial activity of the polymer coating. 

 NOTE: ​Zoono Microbe Shield is used in conjunction with routine cleaning procedures and does not mean that as a result cleaning frequency can be reduced. 

 Uses include:

Floors

Kitchens/bathrooms

Door & tap handles

Any other common touch points

Retail, Manufacturing, Medical, Construction, Health Care, Transport & Aviation Industry.

Use Zoono safely. Always read the label.

Currently available in 5 litre bottles only.

(BULK BUY ORDERS AVAILABLE ON REQUEST)

Please email sales@htspares.co.uk for all enquiries.

PRODUCT DETAILS & SPECIFICATIONS Zoono Hand Sanitiser 

 Zoono Hand Sanitiser is an antimicrobial hand disinfectant that also provides a polymer residual biocide that adds extended protection as it bonds covalently to the skin.  Hands will require washing and or clean prior to application using the hand washing technique recommended by the NHS to cover all exposed skin on the hands especially fingertips. 

 Zoono Hand Sanitiser has been tested to EN 1276, 1500 and 14476 for efficacy against bacteria, fungi, yeasts and enveloped viruses.  In the absence of any official EN/BSI residual antimicrobial hand sanitiser testing the method used was a modified ASTM E3058 method for in vitro skin (synthetic skin)*.  A reduction of bacterial numbers was found after 24 hours but the test did not mimic skin abrasion nor natural loss of epidermal cells nor handwashing with other hand sanitizing products.  

 The Zoono Hand Sanitiser is safe to use on the skin and is alcohol free and based on quaternary ammonium technology. 

 *test results for the modified ASTM E3058 method available on request. 

DIRECTIONS FOR USE: 

Apply 3ml of product to clean hands and cover all surfaces of the hands. Rub hands for 30 seconds, until dry. Apply product as required.

We recommend ZOONO® is used in conjunction with routine hand hygiene procedures.

Use Zoono safely. Always read the label.

Classified as Class 1 Medical Device, this 3 Ply Medical Mask Type IIR performs at a Bacterial Filtration Efficiency of ≥98% and is blood and fluid resistant. Extremely comfortable and breathable, this mask is ideal for biological, chemical and hygiene environments. Soft comfortable elasticated ear loops and adjustable nose-bar for a perfect fit. Suitable for single use only. Dispenser box of 50.

Features

Standards

EN 14683 TYPE IIR

93/42/EEC Class 1 Medical device

Multi-Use Wonder Wipes have become the first choice wipe of the Construction, engineering, Manufacturing Industries and tradesmen. Specially formulated to clean hands, tools and surfaces from wet and semi-cured paint, sealant, adhesive, bitumen, expanding foam, oil, grease and even silicone. Particularly useful when there is no water on site. Available in dispensing tubs. Everbuild Wonder Wipes now contain a powerful Anti-Bacterial Additive that is tested by an independent laboratory to the standards for killing bacteria on dirty surfaces and hands. Resistant to MRSA, Salmonella, Listeria and E.Coli.

OPTREL Clearmaxx PAPR SYSTEM - AIR PACKAGE C/W E3000X WITH 18HR BATTERY

clearmaxx The new grinding helmet from optrel The passive welding helmet of the new optrel p500 series! The new DIN 11 helmet out of the optrel pro-line meets all sorts of needs: safe protection, comfort and consistent quality make the optrel p505 an optimal working tool for pro and occasional welders. In addition to the shade level DIN 11 (ex works), passive filters from DIN 8 - 13 are available. Respiratory Protection Hard Hat Adapter Easy to Use True Color View Warranty Extension 2+1 Years Parking Buddy Lightweight Patented Excenter Fields of Application Grinding Automotive industry Building industry Chemical industry Refrigeration industry Food Industry General industry Heavy metal industry Painting industry Industrial cleaning industry Certificates   Technical Data Classification EN166 Optical class = 1 EN175 Mechanical strength = BT Shape stability Grinding mask up to 220°C / 428°F Front cover lens up to 137°C / 279°F Colour black unpainted Operating temperature -10°C to + 70°C / 14°F to 158°F Storage temperature -20°C to + 80°C / -4°F to 176°F Weight 334g / 11,782 oz Standards Grinding helmet: EN 166 / EN 175 / EN 12941:1998 TH3 / complies with CSA Z94.3, ANSI OS Z87+, EAC PAPR helmet EN 166 / EN 169 / EN 170 / EN 12941:1998 TH3 Scope of delivery clearmaxx helmet with clear polycarbonated front cover lens and instruction manual. Warranty 2 years from date of purchase for manufacturing and material defects.

The Rogue is a robust and durable power source for the professional welder. The machine provides state-of-the-art welding performance and reliability through use of the latest high performance power electronics and Digital control; ensuring a precise consistent arc.
The Rogue provides a smooth DC (Direct Current) welding power which allows you to weld a variety of metals, such as alloyed and non alloyed steel, stainless steel, and cast iron. The Arc Force and Hot Start settings are adjustable and help the user find exactly the right arc for the job. Being digital the Micro-processor precisely controls all functions and provides Best-in Class welding performance across the amperage range of the machine. The Rogue can be used with electrodes up to 4.0mm Ø.
The Rogue can easily perform TIG -welding using a “Live TIG” start. Equip the power source with the optional TIG-Torch, which has a built-in gas valve and a regulator, and a bottle of gas and you are ready to weld mild steel or stainless steel, with or without filler material.

Features

• Superior Arc characteristics –Smooth, Stable performance.

• Generator Compliant –Suitable for use with generators (recommended 7 kW).

• Easy to Use –Set the welding current and weld with excellent results

• Practical Design -makes the power source easy to carry which enables use at almost any work site

• Robust Design –IP23S Designed for Fabrication Shop or Site application.

• PFC ensures a stable arc, resistant to power fluctuations even while working on long extension cables up to

• 100 m (PRO version only)

• Optional analogue remote control (PRO version only)

Industries

• Agricultural Equipment

• Civil Construction

• Industrial and General Fabrication

• Repair and Maintenance

Dimensions

• Height	264 mm
  Length	403 mm
  Width	153 mm

Input Voltage

• Frequency	50/60 Hz
  Phase	1
  Voltage	230 ±15% VAC

• • Power Specifications

    Model	ES 150i	ES 180i	ES 180i PRO*	ES 200i PRO*
    Current Range(A)	10-150 A	10-180 A	10-180 A	10-200 A
    Energy Save Mode	50 Watt	50 Watt	50 Watt	50 Watt
    Max Output (A)	150 A	180 A	180 A	200 A
    Open Circuit Voltage	63 VDC	63 VDC	78 VDC	78 VDC
    Protection Class	IP23S	IP23S	IP23S	IP23S

  • Specifications

    Operating Temp	-10 to +40 °C
    Standards	CE

    Weight

    
      200i PRO
    

    Weight

    8.4 kg

  • Welding Output

    ES 200i PRO*	25 %	200 A	28.0 V	MMA
    ES 200i PRO*	60 %	129 A	25.2 V	MMA
    ES 200i PRO*	100 %	100 A	24.0 V	MMA
    ES 200i PRO*	25 %	200 A	18.0 V	TIG
    ES 200i PRO*	60 %	129 A	15.2 V	TIG
    ES 200i PRO*	100 %	100 A	14.0 V	TIG

Safety Never Felt So Comfortable 

Optrel has launched a brand-new ventilated half mask, Swiss Air  This product has been designed as a revolutionary PAPR system with TH3 certified particle master filter, a adjustable airflow 100-130 l/min and a 14hr power pack. This half mask completely covers the mouth and nose area supplying users with purified air to create a breathing space. Swiss air has positive pressure that supports the user in breathing and eliminates tiring breathing resistance. Being made with high-tech fabric is designed in a way that is adapted to the individual thanks to a freely adjustable headband without any need for fit tests that are common within the half mask.
The Swiss Air protective mask system brings clean breathing air into your environment and lets you breathe as freely as you can. Many industries and public areas produce pollutants such as smoke, soot particles, particulate matter, nitrogen oxides, ozone or viruses that can enter the lungs through the nose, throat and trachea.

Slim, ergonomic, light as a feather. This is how the swiss air presents itself at first glance. A second glance reveals its technological leadership. The core element of this solution is a ventilated half mask that completely covers the mouth and nose area and constantly supplies it with purified air (according to TH3 standard). A breathing space is created in the mouth and nose area which, thanks to positive pressure, supports the user in breathing and eliminates tiring breathing resistance. In this way, the user is permanently in an "overpressure air system" which permanently protects his airways against contaminated air. The half mask, made of high-tech fabric, is designed in such a way that it can be excellently adapted to the individual thanks to a freely adjustable headband. This concept eliminates the need for time-consuming fit tests that are common with conventional half masks.
Clean air is supplied through the Y-hose by a miniaturised blower system, which is comfortably carried by the wearing unit on the back. The filter unit is 45mm narrow and weighs just 550g - a new record that leads to a significant reduction in neck and back pain.

Always with the customer in mind, Optrel strives to combine new technology with current and acute customer needs. As usual, the brand value always remains recognisable and stands for quality - swiss made. However, Optrel goes one step further.  Trees are certainly the best suppliers of fresh air on our planet. For the sale of every single Optrel swiss air respiratory protection system, Optrel therefore plants a tree as part of a global reforestation project, thus more than compensating for the swiss air's carbon footprint. Because fresh air is important for all of us.

     Functions 

• Ventilated half mask made of fire-resistant material covers mouth and nose area completely. Positive pressure supports breathing and avoids fatigue.
• Infinitely adjustable headband for all sizes from XS to XL.
• Y-hose with adjustable neck strap and flexible hose elements guides the air directly into the half mask.
• Shoulder harness for ergonomically perfect weight distribution of the super-light filter system (only 550 g).
• Powerful TH3 filter unit with innovative, ultra-flat design. Lightweight and comfortable to carry, highly efficient in use.
• Blower unit with automatic air flow calibration and 14h high performance battery for an uninterrupted working day.

     Health benefits include

• Health – Permanent protection of the respiratory tract and lungs against pollutants in the air, regardless of the current activity in the working day. This prevents the development of respiratory and lung diseases.
• Ergonomics – Reduction of pain in the neck and back due to a significant reduction in the weight of the head, face and eye protection systems. Heavy combination helmets are no longer necessary.
• Performance – Increase the performance of users thanks to the positive pressure system, which supports breathing and does not cause any breathing resistance.
• Cost savings – Lowering investment costs due to the elimination of costly fitting test. Reduction of running costs due to the massive saving of paper masks as well as their disposal.
• Security of supply – Thanks to a reusable half-mask system, supply is guaranteed at all times, even in the event of a shortage in times of crisis.
• Independence – Swiss air can be used completely self-sufficient, which allows maximum versatility in combination with the appropriate manufacturer-independent occupational health and safety

     Fields of Application

• Welding
• Grinding & Polishing
• Plasma & Oxy Fuel Gas Cutting
• Automatic industry
• Woodworking
• Building industry
• Demolition
• Recycling & Waste Disposal
• Chemical industry
• Refrigeration industry
• Food Processing industry
• General industry
• Heavy metal industry
• Industrial cleaning industry. 
• Medical & Health Care
• Laboratory & Pharmaceutical
• Veterinary 
• Agricultural
  
• Construction
• Rail Industry 

    Specification

Type: Swiss air PAPR system, battery powered unit.

 

Protection level: TH3 (EN12941)

 

BLOWER UNIT

 

Flow rates

level 1: min. 100 l/min
level 2: min. 115 l/min
level 3: min. 130 l/min
All levels with automatic air flow control (levels are set directly on the fan and can be continuously adjusted via the control panel at the front).

 

Material - PA66 GF30

Fan - high quality ball bearing motor

Fuse - electronic

Noise - max. 70db (A)

 

Alarm
optical (with swiss air Control Panel) and audible alarm for low / very low battery, clogged filter, no filter, and low flow
Low battery: alarm period: 3.0s (1.5s on, 1.5s off)
Filter: alarm period 0.5s (0.25s on, 0.25s off)

 

Dimensions (L x W x H) - 250 x 170 x 50 mm

Weight - 1200 g / 42,15 oz (incl. filter, belt, and battery)

Colour - Black

 

HALF-MASK

 

Material - Ripstop textile (98% polyester and 2% polyurethanes
Inlay: Polyurethane foam

Valves - 2 exhalation valves with silicone membrane

Colour - Black

 

HEADBAND / NECK BAND

 

Material - Neoprene / elastic

Colour - Black

 

FILTER UNIT

 

Type - TH3P R SL filter for TH3P System (EU) with pre-filter

 

HOSE

 

Material - POM and silicone

Length - 180 mm (elastic, up to 355 mm excl. Y-hose)

Internal diameter - 21 mm

Colour - Black

 

BATTERY PACK

 

Type - Li-Ione, rechargeable, 3,6 V / 6,5 Ah / 23.4Wh

 

Operating time

level 1: 14h
level 2: 12h
level 3: 8h
(with new filter at room temperature)

 

Charging time – Approximately. 6 hours

 

Sleep mode - After 3 hours, activation by pressing once, start at second press.

 

CERTIFICATES

 

Standards
EN 12941
Europe: TH3
Australia: P3
AS/NZS 1716
EAC TP TC 019/2011

 

Notified body - CE 1024

 

Items Included
Blower unit with hose, half-mask, TH3P R SL filter, battery, harness, charger, charging cable user instructions.

 

Warranty
HTS offers  full Service Warranty as an Authorised Service Centre for Optrel Systems, Offering  a comprehensive 2 years warranty  from date of purchase for manufacturing and material defects, no warranty for battery.

 

Note
The Optrel SWISS AIR respiratory system may NOT be used in environments where there is an immediate danger to health or life (IDLH), in atmospheres containing less than 17% (Europe) oxygen or where the concentration of toxins is so high that a protection class in excess of TH2 (EU) is required. It is NOT evaluated as an ignition source in flammable or explosive atmospheres.

Portwest - CV22 - 2-Ply Anti-Microbial Fabric Face Mask (Pk25) Black

2-ply reusable fabric mask with anti-microbial finish. Kills 99.9% of bacteria and controls numerous odour-causing microorganisms that can accumulate in the fibres from skin contact and laundering. 100% cotton fabric for all day comfort. Elasticated ear loops with adjuster for the perfect fit. Machine washable at 60 degrees. Folded flat, each mask is packed inside an individual hygienic poly bag. 25 masks per retail box.

Features

• Retail box which aids presentation for retail sales

• Individually wrapped inside hygienic polybag

• Reusable and machine washable at 60 degrees

• 2 layers of 100% cotton fabric for ultimate breathabilty and all day comfort

• Anti-microbial finish Texpel MicroTM, kills 99.9% of bacteria

• Controls numerous odour-causing microorganisms that can accumulate in fibres from skin contact and laundering

• Keeps face fresh, dry and odour free

• Soft-to-touch cotton for ultimate wearer comfort

Washcare

Description  

ZOONO® HandSanitiser forms an antibacterial shield that bonds to skin and is effectiveagainst 99.9% of bacteria and a broad range of pathogens,helping to keep hands hygienic for longer. Effective for up to 24 hours. 

• Water based
• Alcohol-free 

Direction For Use:

Apply 3ml ofproduct to clean hands and cover all surfaces of the hands. Rub hands for 30seconds, until dry. Apply product as required.

 

Available Sizes:

50ml, 150ml, 500ml

 

We recommend ZOONO®is used in conjunction with routine hand hygiene procedures.

Use Zoono safely.Always read the label.